CA200_2007Enacted

Vehicle Dismantling and Recycling Industry Environmental Planning Regulation - 200/2007

Jurisdiction:
Canada
Type:
EPR · Other
Last action:
Jan 1, 2007
VehiclesMetalsPlastic PackagingHazardous Materials
Next steps for producers

Confirm your obligations under this measure and track its implementing rules

Applies toAny person that operates or plans to operate a facility engaged in the vehicle dismantling and recycling industry that dismantles more than 5 wet vehicles in a calendar year

Obligations under this law
  • ·Have an individual environmental management plan (EMP) for waste management, reduction or prevention, OR be a member of an association that has an EMP
  • ·Register with a director providing: full legal name, local contact details, facility address and legal land description, address where plan may be viewed, confirmation of plan compliance or association membership details
  • ·Ensure the EMP is approved by a qualified professional
Program page →

No designated program action is recorded for this measure yet — treat the above as the general obligation and verify against the source text.

Regulation establishes environmental management plan requirements for vehicle dismantling and recycling facilities, advancing product stewardship and circular economy principles for end-of-life vehicles; enacted in 2007 but foundational to vehicle EPR infrastructure.
Covered Products
  • ·Wet vehicles (motor vehicles no longer used for transportation that have not been reduced to a steel hulk or steel hulk with only plastic, fabric, or foam components attached)
  • ·Waste streams from wet vehicles: ozone depleting substances and other halocarbons, oils, brake fluids, solvents, fuels and other hydrocarbons, antifreeze, lead and lead-acid batteries, tires, mercury switches, windshield washer fluid
Producer Obligations
  • ·Have an individual environmental management plan (EMP) for waste management, reduction or prevention, OR be a member of an association that has an EMP
  • ·Register with a director providing: full legal name, local contact details, facility address and legal land description, address where plan may be viewed, confirmation of plan compliance or association membership details
  • ·Ensure the EMP is approved by a qualified professional
  • ·Ensure the EMP describes how each regulated waste stream will be removed from wet vehicles
  • ·Ensure the EMP describes how each waste will be stored, treated, recycled or disposed of in compliance with the Act and applicable regulations
  • ·Ensure the EMP sets out management processes for minimizing or eliminating discharge of wastes to the environment
  • ·Ensure the EMP includes a contingency plan for emergency procedures
  • ·Maintain the plan at all times and amend as necessary to ensure ongoing compliance with the Act and applicable regulations
  • ·Keep an up-to-date copy of the plan and applicable report at the address listed in the registration form
  • ·Produce the plan or report to a director or officer on request
  • ·Provide written notice to a director within 30 days of any change in registration information, ceasing to operate the facility, or ceasing to dismantle more than 5 wet vehicles in a calendar year
  • ·Individual facility operators (not association members): have a biennial compliance report prepared by a qualified professional
  • ·Individual facility operators: review, amend or replace the plan within 3 months after each 5th anniversary of effective registration date, with qualified professional approval
  • ·Association members: ensure association reviews, amends or replaces the plan within 3 months after September 1, 2013 and each 5th anniversary thereof, with qualified professional approval
Exemptions
  • ·Facilities that dismantle 5 or fewer wet vehicles in a calendar year are not required to have an EMP or register
  • ·Vehicles that have already been reduced to a steel hulk (or steel hulk with only plastic, fabric, or foam components) are not considered 'wet vehicles' and are not subject to the waste removal requirements
Key Deadlines
Sep 1, 2008compliance: Facilities operating on or before September 1, 2008 must have an EMP and be registered by this date
Sep 1, 2008registration: Facilities operating on or before September 1, 2008 must register with a director by this date; new facilities must register before beginning operations
Sep 1, 2010reporting: Association first reporting period ends; report must be completed within 3 months after September 1, 2010 (i.e., by December 1, 2010)
Sep 1, 2013reporting: Association plan review deadline: within 3 months after September 1, 2013 (i.e., by December 1, 2013), association must review, and if necessary amend or replace, the plan with qualified professional approval
—other: Individual facility operators: plan must be reviewed, amended or replaced within 3 months after each 5th anniversary of effective registration date
—reporting: Individual facility operators: biennial compliance report must be completed within 3 months after the end of each 2-year reporting period from date of registration
—reporting: Associations: biennial compliance report must be completed within 3 months after the end of each 2-year period (first period ending September 1, 2010, then every 2 years)
—other: Written notice of registration changes or cessation of operations must be provided to a director within 30 days of the change
Producer Definition
Any person that operates or plans to operate a facility engaged in the vehicle dismantling and recycling industry that dismantles more than 5 wet vehicles in a calendar year
Enforcement
Director or officer under the Environmental Management Act (British Columbia): Fine of not more than $200,000 on conviction for: failing to have a plan, failing to register, having a plan or registration with false or misleading information, failing to have a plan reviewed/amended/replaced by a qualified professional within required period, failing to have a required report prepared, having a non-compliant or false/misleading report, or failing to maintain the plan. Penalties apply to individual operators, incorporated associations, each member of an unincorporated association, and individual members of incorporated associations (subject to defences in section 8(4)).
Preemption Notes
This is a provincial British Columbia regulation under the Environmental Management Act. No preemption provisions are referenced in the regulation text.
Compliance Dimensions
PenaltiesUp to 200000 CAD per violation

“A person described in section 2 (1) who is not a member of an association commits an offence and is liable on conviction to a fine of not more $200 000 if the person does any of the following: a fails to have a plan when required under section 2 (2); b fails to register with a director when required under section 2 (2); c has a plan that contains false or misleading information; d provides false or misleading information in a registration form; e fails to have a reviewed, amended or replacement plan approved by a qualified professional within the period established by section 2 (4); f fails to have a report prepared when required under section 4 (1); g has a report prepared that i does not comply with section 4 (2), or ii contains false or misleading information; h fails to maintain the plan as required under section 6.”

PRO StructureIndividual

“association means an association of two or more facilities, which association includes in its purposes a preparing a plan for the purposes of this regulation, and b monitoring and reporting on compliance with the plan; A person that operates or plans to operate a facility that dismantles more than 5 wet vehicles in a calendar year must a either i have an environmental management plan for waste management, reduction or prevention, or ii be a member of an association that has an environmental management plan for waste management, reduction or prevention”

Tracking dates like these across a whole portfolio of jurisdictions is what Upcoming Deadlines does.

Full bill text

200/2007
O.C. 447/2007
June 21, 2007
September 1, 2007
Environmental Management Act
Vehicle Dismantling and Recycling Industry Environmental Planning
Regulation

Definitions
1
In this regulation:

Act means the Environmental Management
Act ;

association means an association of two or more facilities, which
association includes in its purposes

a
preparing a plan for the purposes of this regulation, and

b
monitoring and reporting on compliance with the plan;

facility means an establishment that is engaged in the vehicle
dismantling and recycling industry;

motor vehicle has the same meaning as in the Motor Vehicle
Act :

plan means an environmental management plan required under section 2
(1);

qualified professional , in relation to a duty or function under this
regulation, means an applied scientist or technologist specializing in an applied science
or technology applicable to the duty or function, including, if applicable and without
limiting this, agrology, biology, chemistry, engineering, geology or hydrogeology and
who

a
is registered in British Columbia with the appropriate professional
organization, is acting under that organization's code of ethics and is subject to
disciplinary action by that organization, and

b
through suitable education, experience, accreditation and knowledge, may be
reasonably relied on to provide advice within their area of expertise;

vehicle dismantling and recycling industry has the same meaning as in
Schedule 2 of the Waste Discharge Regulation;

wet vehicle means a motor vehicle that

a
is no longer used for transportation purposes, and

b
has not been reduced to a steel hulk or to a steel hulk with only the plastic,
fabric or foam components still attached.

Requirement for an environmental management plan
2

1
A person that operates or plans to operate a facility that dismantles more than 5
wet vehicles in a calendar year must

a
either

i
have an environmental management plan for waste management, reduction or
prevention, or

ii
be a member of an association that has an environmental management plan for
waste management, reduction or prevention, and

b
register with a director under section 3.

2
A person must comply with subsection (1),

a
if operating the facility on or before September 1, 2008, on or before that
date, and

b
otherwise, before beginning to operate the facility.

3
A plan for the purposes of this section must

a
be approved by a qualified professional,

b
describe how each of the following wastes will be removed from wet vehicles at
facilities to which the plan applies:

i
ozone depleting substances and other halocarbons;

ii
oils, brake fluids, solvents, fuels and other hydrocarbons;

iii
antifreeze;

iv
lead and lead-acid batteries;

v
tires;

vi
mercury switches;

vii
windshield washer fluid,

c
describe how each waste referred to in paragraph (b) will be stored,
treated, recycled or disposed of in compliance with the Act and applicable regulations,
and

d
set out

i
management processes for minimizing or eliminating the discharge of wastes to
the environment, and

ii
a contingency plan documenting procedures to be followed during an
emergency.

4
Within 3 months after each 5th anniversary of the date their registration is
effective under section 3 (2), a person operating a facility for which there is a plan
specific to the facility must

a
review the plan,

b
amend or replace the plan if necessary to ensure that that person has a plan
that complies with subsection (3), and

c
have the reviewed, amended or replacement plan approved by a qualified
professional.

5
Within 3 months after September 1, 2013 and within 3 months of each fifth
anniversary of that date, an association that has a plan for 2 or more facilities
must

a
review the plan,

b
amend or replace the plan if necessary to ensure that the association has a plan
that complies with subsection (3), and

c
have the reviewed, amended or replacement plan approved by a qualified
professional.

Registration
3

1
A person described in section 2 (1) must register by providing all the
following information to a director in a form approved by the director:

a
the full legal name of the individual, partnership, corporation or other entity
operating or planning to operate the facility;

b
the name, address and telephone number of an individual who is located at or
near the facility and is the local contact for the facility;

c
the address of the facility and the legal description of the land on which the
facility is located;

d
the address at which the plan that applies to the facility may be viewed or
copied;

e
confirmation that the facility has a plan that complies with section 3, or is a member of an association that has a plan that complies with section 3 and the name, address and telephone number of that
association;

f
any other relevant information the discharger wishes to provide.

2
Registration under this section takes effect on the date a complete registration
is received by a director.

3
A person registered under this section must provide a director with written notice
within 30 days after

a
a change in information provided in the person's registration, or

b
ceasing to

i
operate the facility, or

ii
dismantle more than 5 wet vehicles in a calendar year.

Reporting by facility
4

1
A person operating a facility that is not a member of an association must have a
report prepared by a qualified professional on the matters described in subsection (2)
(b)

a
for the period up to the date that is 2 years after the date of registration
under this regulation, and

b
for each 2-year period after that date.

2
A report under subsection (1) must

a
be in writing,

b
describe

i
how the wastes described in the plan for the facility were managed,

ii
whether the management of those wastes was in accordance with the plan,
and

iii
the effectiveness of the management processes used for minimizing or
eliminating the discharge of wastes to the environment, and

c
be completed within 3 months after the end of each 2-year period described in
subsection
(1).

Reporting by association
5

1
An association that has prepared a plan for more than one facility must have a
report prepared by a qualified professional on the matters described in subsection (2)
(d)

a
for the period up to September 1, 2010, and

b
for each 2-year period after that date.

2
A report under subsection (1) must

a
be in writing,

b
provide the name and address of each facility to which the plan
applies,

c
specify how many members of the association were audited for compliance with the
plan and the identity of each of those members, and

d
describe

i
how the wastes described in the plan were managed by each facility
audited,

ii
whether the management of those wastes was in accordance with the plan,
and

iii
the effectiveness of the management processes used for minimizing or
eliminating the discharge of wastes to the environment, and

e
be completed within 3 months after the end of each period described in subsection
(1).

3
An association that has at least 3 members must audit

a
one third of its members for a report under this section, and

b
each of its members at least once in the course of completing 3 consecutive
reports under this section.

4
An association that has 2 members must audit

a
one member for a report under this section, and

b
each of its members at least once in the course of completing 2 consecutive
reports under this section.

Maintaining a plan
6
At all times, a person operating a facility that has its own plan, and an
association that has a plan for 2 or more facilities, must maintain the plan, and amend it
as necessary, so that if a person complies with the plan, the person also complies with the
requirements of the Act and applicable regulations.

Records
7

1
A person described in section 2 (1) must keep, at the address required under
section 3 (1)
(d) for the person's registration form, an up-to-date copy of the plan that
applies to the facility, and the report prepared under section 4 or 5, as applicable, in
relation to the plan.

2
On request of a director or officer, a person described in subsection (1)
must produce the plan or report to the director or officer for inspection or
copying.

Offences and penalty
8

1
A person described in section 2 (1) who is not a member of an association
commits an offence and is liable on conviction to a fine of not more $200 000 if the
person does any of the following:

a
fails to have a plan when required under section 2 (2);

b
fails to register with a director when required under section 2
(2);

c
has a plan that contains false or misleading information;

d
provides false or misleading information in a registration form;

e
fails to have a reviewed, amended or replacement plan approved by a qualified
professional within the period established by section 2 (4);

f
fails to have a report prepared when required under section 4
(1);

g
has a report prepared that

i
does not comply with section 4 (2), or

ii
contains false or misleading information;

h
fails to maintain the plan as required under section 6.

2
An incorporated association, or each member of an unincorporated association, that
does any of the following commits an offence and is liable on conviction to a fine of not
more than $200 000:

a
fails to have a plan prepared when the facilities to which the plan relates are
required under section 2 (2) to have a plan;

b
has a plan that contains false or misleading information;

c
fails to have a reviewed, amended or replacement plan approved by a qualified
professional within the period established by section 2 (5);

d
fails to have a report prepared when required under section
5;

e
has a report prepared that

i
does not comply with section 5 (2), and with section 5 (3) or (4) as
applicable, or

ii
contains false or misleading information;

f
fails to maintain the plan as required under section 6.

3
A member of an association commits an offence and is liable on conviction to a
fine of not more $200 000

a
whether or not the association is incorporated, if the person

i
does not have a plan,

ii
fails to register with a director when required under section 2
(2),

iii
has a plan that includes false or misleading information, or

iv
provides false or misleading information in a registration form,
and

b
if the association is incorporated and the association

i
fails to have a plan reviewed, amended or replaced when required under
section 2
(5),

ii
fails to have a report prepared when required to do so under section
5,

iii
has a report prepared that

A
does not comply with section 5 (2), and with section 5 (3) or (4) as
applicable, or

B
contains false or misleading information, or

iv
fails to maintain the plan as required under section 6.

4

Subsection (3)
(b) does not apply to a member if the member,

a
in relation to subsection (3) (b) (i), has a reviewed, amended or replacement
version of the association's plan approved by a qualified professional when the
association is required to do so under section 2 (5),

b
in relation to subsection (3) (b) (ii), has a report on the association's plan
prepared under section 4 when the association is required to do so under section
5,

c
in relation to subsection (3) (b) (iii), when the association is required to
have a report prepared that complies with section 5 (2), and with section 5
(3) or (4) as applicable, has a report prepared that

i
complies with section 4 (2), and

ii
does not contain false or misleading information, and

d
in relation to subsection (3) (b) (iv), maintains the association's plan as
required under section 6.

[Provisions of the Environmental Management
Act , S.B.C. 2003, c. 53, relevant to the enactment of this regulation:
sections 21, 138 and 139]

Full text as ingested. Verify against the official source above.

Explore more circular-economy legislation on the Atlas Circular legislation tracker.